Ultimaker Timing Pulleys 3d models

A combination of http://www.thingiverse.com/thing:2079 and http://www.thingiverse.com/thing:3474 provides a solution for all your pulley requirements.

On my profile, I have a GM350 that fits perfectly. ...The pulleys and accessories are also compatible with other models, requiring only minor adjustments.

Given for replacement in a Ditto 3D Printer, the long and short pulleys were received due to multiple broken ones on the device.

A collection of intricately designed 5m pulleys, each carefully crafted with precision engineering, awaits your attention. The Teeth and Bore of these marvels stand out prominently, a testament to the skill that went into their creation. ... The width...

... ...Originally intended for my RC truck, these pulleys could also be used for various other projects requiring such a setup. ...After printing the first few in PLA, they appear to be holding up well so far, but ABS may prove more suitable at high RPMs.

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler_ht = 1.5 nut_shaft_distance = 1.2 additional_tooth_width = 0.2 m3_dia = 4 no_of_nuts = 2 pulley_t_ht = 8 m3_nut_hex = 3...

The original components like nuts, screws, pulley, and washer are reused except for the one holding the pulley down; that got swapped out with a longer version (25mm). If you're careful, securing the fishing line to the reel holder or somewhere else...

This is some OpenSCAD code to make pulleys and gears with changeable tooth length. ...I made this to allow for more options for experimenting with different generators on my "Mini Wind Power Project".

The pulley system allows for easy direction changes and guidance of lines, transforming vertical to horizontal or vice versa. ...As a basic machine design project, it's straightforward yet effective.

Make a duplicate of the HTD-5-master, then alter the parameter for Teeth and so on to generate a fresh pulley. ...It's located within Manage/Parameters in Inventor.

... a Stable and Secure Operation. To Accommodate the Smaller Pulley, a Minor Adjustment was Made, Involving the Drilling of a Hole to Allow the Cord to Exit at the Base and Attach to the Handle, Providing a Smooth and Efficient Lifting Experience.

Once I bought some pulleys to hold my ladder up to the ceiling, but they were not strong enough one day they broke. So I designed new pulleys, and I designed them in such way outside would look the same, both halves would be the same so sides with...

Options: - base height: set to 6mm - toothed part length: extended to 9mm - retainer height: adjusted to 1.5mm - belt retainer setting: activated for one slot - idler height adjustment: made to 1.5mm - nut shaft distance from center: decreased by...

You'll need two halves for whichever pulley you make, and two end buttons (these buttons will space the outside of the pulley about 1.5mm from the surface the button gets mounted to). Best to put a drop of superglue inside the assembled halves. The...

You'll need two halves for each pulley you make, and two end buttons (these buttons will space the outside of the pulley about 1.5mm from the surface the button gets mounted to). It's best to put a drop of superglue inside the assembled halves. The...

Instructions You can assemble the pulleys using M3 screws and M4 nuts on both sides; you'll see how they fit together from the accompanying pictures. There are two models available: One set of symmetrical parts that can be glued together, slightly...

Create both versions of the pulley as per the design, with an alternative using a male/female assembly instead of wooden dowels. For added convenience, use a single 3mm x 22 cap screw in the center to fasten the parts together. To ensure smooth...

... shafts are 5 and 8mm, which I think is more common anyway). The "x*" in the name indicates the number of copies needed for each part. I made these pulleys for my own use but feel free to print as many as you like to suit your project's needs.

this are different types of pulleys use in v12 engine belt guide. This model is the extension to the v12 engine model series, please check out my profile of other components. ...Do follow to get see future uploads of other components.

Perfect for limited areas, these custom low-load pulleys are ideal for swift prototyping. Available in 3/4" and 1" diameters, they can be combined co-axially to form a belted reduction system. ...The hub is designed to fit a 1/2" hexshaft.

Sheaves rope pulleys with standard groove according to DIN 15061.For wire rope with diameter from 3mm up to 26mm.Sheaves diameter from 100mm to 450mmnew dimensions can be simply added.Solidworks part file with all configurations and step file for...

A single file contains multiple 5M HTD pulleys with belt widths of 9, 15, and 25 mm. Adjustable configuration table allows for value changes if needed. If the file size is too large, unnecessary data can be deleted. ...Drawings are available to help...

this are different types of pulleys use in v12 engine belt guide. This model is the extension to the v12 engine model series, please check out my profile of other components. ...Do follow to get see future uploads of other components.

Here are the Instructions for assembling this customized belt-driven pulley: First, use the provided options to customize the following features: - Adjust the screws disposition to setting 2 - Choose a base diameter of 32 units - Set the toothed part...

I crafted my own pulley designs after trying numerous alternatives and they serve their purpose remarkably well. Assembly Instructions: You can employ M3 screws paired with M4 nuts on both sides; their compatibility will be evident. Visual...

http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Using the following settings: Number of Teeth: 20 Screws Disposition: Along Inner Circle (2nd option) Base Height: 8mm Retainer Height: 1.5mm Toothed Part Length: 11mm Base Diameter: 20mm...

I designed these two simple reels for our FTC team's (11591) pulley lift system. We utilize 80lb braided fishing line to attach the reel to a Tetrix motor hub with the bump facing towards the motor, then tie the string through the adjacent hole and...

This is a really fun project to do with kids (or without) to learn about pulley systems and how they work and a fun toy to have at the end of it too! I printed all pieces without supports - you'll need one of each part and 4 of the bobbins plus...

Profile set to Six Nutmeg Shaft Distance adjusted to Two Millimeters Motor Shaft Diameter resized to Sixty-six Percent of its Original Value Number of Teeth precisely measured at Twenty units Retainer Height customized for precise alignment,...

Simple Timing Belt Tensioner 8 on 8 mm for Ultimaker